HealthmateForever ZT15AB Series TENS Unit EMS/PMS Electronic Pulse Massager

Scratch & Dent ZT15AB TENS Unit & Muscle Stimulator

  • $ 27.99
  • Save $ 6.00

  • 1 FDA cleared Class II OTC HealthmateForever ZT15AB electroTherapy device (combined TENS unit and Muscle Stimulator)
  • 8 piece self-adhesive conductive reusable Pin-inserted electrode pads
  • 1 Pads Holder
  • 4 sets of Pin-inserted electrode wires (3.5mm plug)
  • User Manual
  • Warranty Card
  • Powered by 3 AAA batteries
  • For User Manual, please email us at
  • If any questions or concern please feel free to contact us.
  • 15 preprogrammed therapeutic methods modes:
    • Custom designed for 9 different conditions: Neck, Shoulder, Back, Elbow, Hip, Ankle, Knee, Foot/Hand, and Wrist;
    • Custom designed for 6 different massage modes: Knead, Acupuncture, Tapping, Cupping, Scraping, and Random.
  • Adjustable 80 minute timer, automatic power savings: shut off when it is not under operation, 
  • 30 levels of adjustable intensity in either channel 1 & 2 or channel 3 & 4. You can treat two different areas with different intensity at the same time, very powerful, very helpful for numbness stimulation and early stroke rehab.
  • Intensity+ button increases strength;
  • Intensity- button decreases strength;
  • 4 outputs design with 2 independent channels 1& 2 and 3 & 4; 
  • Allows 8 pads to be used at the same time in the two different targeted areas;
  • Your TENS EMS uses 3 AAA batteries;
  • Easy to read animated back-lit Large LCD Display
    • Mainly designed for senior citizens and chronic pain relief
  • If any questions or concern please feel free to contact us.

Electronic pulse massager Output Parameters:

  • Output pulse width: 90 μS ± 15%
  • Pulse Frequency: <100 HZ
  • Max output amplitude: <5v (r.m.s)
  • Electrode wire plug diameter 3.5 mm

Input Parameters:

  • Input voltage: DC 4.5 V
  • Rated current:   ≤ 50 mA
  • Rated power:  0.225 W 
  • Temperature range: 0°C to 48°C
  • Humidity: 10% to 85%
  • Atmospheric Pressure: 400 hPa to 1060 hPa
  • Electronic Pulse Massager Size:
  • Screen size: 1.75" W x 1.75" L
  • Size: 3.5" L x 2.25" W x .75" T
  • Weight: 4.4oz
  • Patent Number: 

If any questions or concern please feel free to contact us.

Step 1: Set up batteries.

  1. Check if the batteries are in good condition.
  2. Remove the battery cover located on the back of the device.
  3. Insert 3* AAA batteries. Make sure the “+” “-” sides correspond.
  4. Put the battery cover back.

Step 2: Connect electrode wires with control unit.

ZT15AB has two independent channels with 4 outputs C1, C2, C3, and C4 combining C1&C2 on one channel, C3&C4 on the other channel. This will allow you to set separate levels of intensity on C1&C2 and/or C3&C4. Before connecting the wires with unit, decide which channels you wish to use.

  1. Plug the electrode wire into the output(s) located at the top of the device. Depending on your needs, you may use one, two, three or four outputs.
  2. Ensure that the electrode wires are fully inserted and secured into the output.
  3. Repeat steps 1 & 2 to connect another wire.

Step 3: Connect electrode pads with wires.

  1. Each wire has two leads with pin-insert connectors. Plug the male pin-insert end on the wire into the female pin-insert connector on the pads. Make sure at least one pair of pads are attached to the same wire.
  2. Remove the plastic films on the pads.

Step 4: Place pads on your body.

Place the pads on the muscle you wish to treat. Place the adhesive side of pad on your skin.

Step 5: Turn on the control unit and select channel.

Press the “ON/OFF” button to turn ON your device.

Verify the channel indicator on the screen to make sure the device is on the same channel you wish to use. 

Step 6: Selecting programs.

You can select any of the 15 programs by pressing the “PRG” buttons. To go from program 1 to program 2, press “PRG” ↑button. To go back from program 1 to program 2 press the“PRG” ↓button.

You CAN NOT use different modes on two channels. All outputs will share the same mode.             

Step 7: Adjust timer.

Press the “TIMER” button to adjust timer.

Step 8: Adjusting the level of intensity.

After selecting the desired program and setting, you can increase the intensity by pressing the intensity buttons on the key pad.

For outputs C1&C2.

Press the “C1.2”↑button to increase the intensity on outputs C1 and/or C2.

Press the “C1.2” ↓button to decrease the intensity on outputs C1 and/or C2.

For outputs C3&C4.

Press the “C3.4”↑button to increase the intensity on outputs C3 and/or C4.

Press the “C3.4” ↓button to decrease the intensity on outputs C3 and/or C4.

Step 9: Turn off the device.

Press the “ON/OFF” button to turn OFF your device.

Step 10: Remove the pads from your skin.

Remove the pads from your skin slowly and place them back on the provided pad holder or the protective plastic film.

Step 11: Take off the pads from wires. Unplug wires from device.