​ ​ ​ ​ ​ ​ ​ ​ HealthmateForever Electronic Muscle Stimulator | TENS units

Pro12ABQ TENS Unit & Muscle Stimulator
Free Gift

  • $ 99.99
  • Save $ 60.00


  • 1 FDA cleared Class 2 OTC HealthmateForever Pro12ABQ electroTherapy device (combined TENS unit and Muscle Stimulator)
  • 4 piece self-adhesive conductive reusable gel pads
  • 2 sets of electrode wires (3.5mm plug)
  • 1 USB Charger/Wall Unit (international travel charger 110V - 240V)
  • 1 pads holder 
  • User Manual
  • Limited Lifetime Warranty Card
  • ATTENTION: Upgrade to Wireless Kit in drop down menu
  • For User Manual, please email us at support@healthmateforever.com.
  • If any questions or concern please feel free to contact us.

 

  • 12 preprogrammed massage modes with different waveforms:
    • Tuina (Push & Pull), Acupuncture, Tapping, Guasha (Scraping), Cupping, Shiatus (Finger Press), Pressure, Back Pain, Deep Tissue Massage, Body Building, Body Building2, and Combination
  • Adjustable 10-80 minute timer
  • 20 levels of adjustable intensity in channel A or channel B.
  • 2 outputs are isolated, so both channel A and channel B has the same 100% power, without reducing strength in half.
  • Allows 4 pads to be applied to the two different targeted areas at the same time;
  • Rechargeable internal lithium battery – up to 10 hours of continuous use
  • Pause Button
  • Easy to read animated backlit LCD Display
  • If any questions or concern please feel free to contact us.
  • Output pulse width: 90μS ± 15%
  • Pulse Frequency: <100HZ
  • Max output amplitude: <5v (r.m.s)
  • Input Voltage: DC5V
  • Rated current: ≤ 50mA
  • Rated Power: ≤ .25W
  • 3.5mm Plug
  • Screen size: 1.5" W x 2" L
  • Size: 4" L x 2" W x .25" T
  • Weight: 2.0 oz

    Patent Number: US D757, 292S

    If any questions or concern please feel free to contact us.

    Step 1: Connect electrode wires with control unit.

    This device is equipped with two isolated channels A&B. This will allow you to set separate modes and separate intensities on each channel. Before connecting the wires to the unit, decide which channel you wish to use (channel A or B). To use A channel only, connect the electrode wire(s) to output A. To use B channel only, connect the electrode wire(s) to output B. To use both A, B channels, please connect wires to all outputs.

    1. Plug the electrode wire into the device.
    2. Ensure that the electrode wires are fully inserted and secured.
    3. Repeat steps 1 & 2 to connect another wire.

    Step 2: Connect electrode pads with wires.

    1. Each wire has two leads with snap-on connectors. Snap the wire connectors onto the snap on buttons on the pads.
    2. Make sure at least one pair of pads is attached to the same wire.
    3. Ensure that the snap on connections are fastened.
    4. Remove the plastic films on the pads.

    Step 3: Place pads on your body.

    Place pads on the muscle you would like to treat. Place the adhesive side of pad on your skin.

    Step 4: Turn on the control unit.

    Push the “ON/OFF” switch.

    The device will start showing all icons for 2 seconds to ensure that all options are displayed properly.

    Step 5: Adjust timer.

    Press the “T” button to adjust timer.

    Step 6: Selecting modes and intensity.

    Once the device is turned ON, it will show all icons for 1 second to ensure that all icons are displaying properly. The unit will automatically set to channel A, mode 1, with zero intensity. As mentioned previously, this device is equipped with two isolated channels A&B. You will need to select the mode and intensity for the channel you wish to use.

    For channel A:

    1. Press the “M” button to cycle through modes.
    2. Keep pressing the “M” button to get to the desired mode.

    Note: You will need to go through all modes to get back to the desired mode.

    1. Press intensity “+” button to increase the intensity.

    Press intensity “-” button to decrease the intensity.

    Note: When changing the mode, the intensity level will automatically reset zero.

    Keep increasing the intensity by pressing the intensity increase button to get to the desired level.

    For channel B:

    Press the channel switch button once to switch to channel B. The B letter will blink to indicate channel B is working. Repeat steps above:

    1. Press the “M” button to cycle through modes.
    2. Keep pressing the “M” button to get to the desired mode.

    Note: You will need to go through all modes to get back to the desired mode.

    1. Press intensity “+” button to increase the intensity.

    Press intensity “-” button to decrease the intensity.

    Note: When changing the mode, the intensity level will automatically reset zero.

    Keep increasing the intensity by pressing the intensity increase button to get to the desired level.

    You have the option to use one channel alone or both channels.

    Step 7: Turn off the device.

    Push the “ON/OFF” switch.

    Step 8: Remove the pads from your skin.

    Remove the pads from your skin softly and place them back on the provided pad holder or the protective plastic film.

    DO NOT remove the pads before you turn off the unit.

    Step 9: Take off the pads from wires. Unplug wires from device.