​ ​ ​ ​ ​ ​ ​ ​ HealthmateForever TENS unit Electrical digital plus impulse massager

NK10GL TENS Unit & Muscle Stimulator
Free Gift

  • $ 59.99
  • Save $ 40.00


  • 1 FDA cleared Class II OTC HealthmateForever NK10GL electrotherapy device (combined TENS unit and Muscle Stimulator)
  • 4 piece self-adhesive conductive reusable gel pads
  • 2 sets of electrode wires (3.5mm plug)
  • 1 USB Charger/Wall Unit (international travel charger 110V - 240V)
  • 1 pads holder
  • User Manual
  • Limited Lifetime Warranty Card
  • ATTENTION: Upgrade to Wireless Kit in drop down menu
  • If any questions or concern please feel free to contact us.
  • 10 preprogrammed massage modes with different waveforms:
    • Tuina (Push & Pull), Acupuncture, Tapping, Guasha (Scraping), Leg, Cupping, Body Building, Body Building2, Foot, and Combination
  • Adjustable 10-60 minute timer
  • 2 outputs working simultaneously.
  • 20 levels of adjustable intensity
  • Allows 4 pads to be used at the same time
  • Rechargeable internal lithium battery – up to 10 hours of continuous use

                
  • Easy to read animated backlit LCD Display
  • If any questions or concern please feel free to contact us.
  • Output pulse width: 90μS ± 15%
  • Pulse Frequency: <100HZ
  • Max output amplitude: <5v (r.m.s)
  • 3.5mm plug
  • Screen size: 1.5" W x 2" L
  • Size: 1.75" L x 3.5" W x .25" T
  • Weight: 1.8oz
  • If any questions or concern please feel free to contact us.

    Step 1: Connect electrode wires with control unit.

    1. Plug the electrode wire into the device.
    2. Ensure that the electrode wires are fully inserted and secured.
    3. Repeat steps 1 & 2 to connect another wire.

    Step 2: Connect electrode pads with wires.

    1. Each wire has two leads with snap-on connectors. Snap the wire connectors onto the snap on buttons on the pads.
    2. Make sure at least one pair of pads is attached to the same wire.
    3. Ensure that the snap on connections are fastened.
    4. Remove the plastic films on the pads.

    Step 3: Place pads on your body.

    Place pads on the muscle you would like to treat. Place the adhesive side of pad on your skin.

    Step 4: Turn on the control unit.

    Push the “ON/OFF” switch.

    The device will start showing all icons for 2 seconds to ensure that all options are displayed properly.

    Step 5: Select modes.

    You can see some different modes on the screen.  

    The device will automatically set to mode 1 with zero intensity.

    “M” is mode changing button. Press “M” button to change mode and select the mode you want to use.

    Press the “M” button to change cycle through modes. Keep pressing the “M” button to get to the desired mode.

    Step 6: Adjust timer.

    Press the “T” button to adjust timer.

    Step 7: Adjust intensity.

    Press the intensity “+”“-” button to set the desired intensity.

    Press intensity “+” button to increase the intensity.

    Press intensity “-” button to decrease the intensity.

    When switching modes, the intensity will automatically set zero. Repeat step 7 after changing the mode.

    You can pause the unit by pressing “pause” button.

    Step 8: Turn off the device.

    Push the “ON/OFF” switch.

    Step 9: Remove the pads from your skin.

    Remove the pads from your skin softly and place them back on the provided pad holder or the protective plastic film.

    DO NOT remove the pads before you turn off the device.

    Step 10: Take off the pads from wires. Unplug wires from device.