​ ​ ​ ​ ​ ​ ​ ​ TENS Muscle Stimulator | Pain Relief | HealthmateForever TS8

Touch Screen TS8 HealthmateForever TENS Unit & Muscle Stimulator

  • $ 69.99
  • Save $ 30.00


  • 1 FDA cleared Class II OTC HealthmateForever touch screen TS8 electroTherapy device (combined TENS unit and Muscle Stimulator)
  • 4 piece self-adhesive conductive reusable gel pads
  • 2 sets of electrode wires (2.5mm plug)
  • 1 USB Charger/Wall Unit (international travel charger 110V - 240V)
  • 1 stylus pen
  • 1 Pads holder
  • User Manual
  • Lifetime Warranty Card
  • If any questions or concern please feel free to contact us.
  • Touch Screen
  • 8 preprogrammed massage modes with different waveforms:
    • Tuina (Push and Pull), Acupuncture, Tapping, Cupping, Guasha (Scraping), Leg massage, Foot Massage, Combination
  • Default Time: 80 minutes
  • Adjustable 10-80 minute timer
  • 2 outputs working simultaneously.
  • 20 levels of adjustable intensity
  • Dual simultaneous output design
  • Allows 2 pads to be used at the same time per output with up to 4 pads
  • Rechargeable internal lithium battery – up to 10 hours of continuous use
  • Easy to read animated backlit LCD Display
  • Belt Clip
  • If any questions or concern please feel free to contact us.
  • Output pulse width: 90μS ± 15%
  • Pulse Frequency: <100HZ
  • Max output amplitude: <5v (r.m.s)
  • 2.5mm plug
  • Screen size: 1.25" Wide by 1" Length
  • Size: 1.75"L x 2.25" W x .75" T
  • Weight: 1.4oz
  • If any questions or concern please feel free to contact us.

Step 1: Connect electrode wires with control unit.

  1. Plug the electrode wire into the device.
  2. Ensure that the electrode wires are fully inserted and secured.
  3. Repeat steps 1 & 2 to connect another wire.

Step 2: Connect electrode pads with wires.

  1. Each wire has two leads with snap-on connectors. Snap the wire connectors onto the snap on buttons on the pads.
  2. Make sure at least one pair of pads is attached to the same wire.
  3. Ensure that the snap on connections are fastened.
  4. Remove the plastic films on the pads.

Step 3: Place pads on your body.

Place pads on the muscle you would like to treat. Place the adhesive side of pad on your skin.

Step 4: Turn on the control unit.

Push the “ON/OFF” switch.

Step 5: Adjust timer

Touch the time (number displayed) to adjust timer.

Step 6: Selecting modes and intensity.

Once the device is turned ON, it will show all icons for 1 second to ensure that all icons are displaying properly.

  1. To select the mode, touch any of the modes displayed on the screen.

Note: The selected mode will blink. 

  1. Press intensity “+” button to increase the intensity.

Press intensity “-” button to decrease the intensity.

Note: When changing the mode, the intensity level will automatically reset zero.

Keep increasing the intensity by pressing the intensity increase button to get to the desired level.

Step 7: Turn off the device

Push the “ON/OFF” switch.

Step 8: Remove the pads from your skin.

Remove the pads from your skin softly and place them back on the provided pad holder or the protective plastic film.

DO NOT remove the pads before you turn off the unit.

Step 9: Take off the pads from wires. Unplug wires from device.